Sheevaplug: Squeeze on SD won't boot on power up

I have a strange problem, or at least one that Google doesn't help me find
an answer too.

I have installed Squeeze on an SD card following the excellent web site by
Martin Michlmayr.

However, my Sheevaplug won't boot after being powered on. If I type "run
bootcmd" atthe Marvell>> prompt, it *does* boot just fine!

After power up, the boot fails so fast that all I (sometimes) get a glimpse
of is:

Error! cmd : 8, err : 0201
Error! cmd : 1, err : 0201
Error! cmd : 1, err : 0201
Error! cmd : 1, err : 0201
Error! cmd : 1, err : 0201
Error! cmd : 1, err : 0201
Error! cmd : 1, err : 0201
Error! cmd : 1, err : 0201
Error! cmd : 1, err : 0201
Error! cmd : 1, err : 0201
Error! cmd : 1, err : 0201
No MMC card found
** Bad partition 1 **
** Bad partition 1 **
## Booting image at 00800000 ...
Bad Magic Number
Marvell>>

If I issue a printenv, I get the results shown below.

What is going on?

The plug runs fine after this manual boot command, but I can't have a serial
connection to it all the time!

Thank,
Mark

printenv results follow:

Marvell>> printenv
baudrate5200
loads_echo=0
rootpath=/mnt/ARM_FS/
netmask%5.255.0.0
console=a0000
e=ttyS0,115200
CASset=min
MALLOC_len=1
ethprime=egiga0
bootargs_root=root=/dev/mtdblock2 ro
ethmtu00
usb0Mode=host
nandEcc=1bit
ethact=egiga0
serverip.10.0.2
ipaddr.10.0.1
cesvcid=ULULULULULULPPULULULULULDA
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console)
root=/dev/m
tdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm
0x2000000;
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu00
yuk_ethaddr:00:00:EE:51:81
netretry=no
rcvrip9.254.100.100
loadaddr=0x02000000
autoload=no
ethaddr:50:43:01:47:74
run_diag=no
arcNumber 97
bootcmd_m0000=0x01100000
bootargs_console=console=ttyS0,115200
bootcmd_mmc=mmcinit; ext2load mmc 0 0x01100000 /uInitrd; ext2load mmc 0
0x00800000 /uImage
bootcmd=setenv bootargs $(bootargs_console); run bootcmd_mmc; bootm
0x00800000 0x01100000
stdin=serial
stdout=serial
stderr=serial
nandEnvBase=a0000
mainlineLinux=yes
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
enaAutoRecovery=yes
pcieTune=no
bootargs=console=ttyS0,115200

Environment size: 1366/131068 bytes


I have a strange problem, or at least one that Google doesn&#39;t help me find an answer too.<br><br>I have installed Squeeze on an SD card following the excellent web site by Martin Michlmayr.<br><br>However, my Sheevaplug won&#39;t boot after being powered on. If I type &quot;run bootcmd&quot; atthe Marvell&gt;&gt; prompt, it *does* boot just fine!<br>
<br>After power up, the boot fails so fast that all I (sometimes) get a glimpse of is:<br><br>Error! cmd : 8, err : 0201<br>Error! cmd : 1, err : 0201<br>Error! cmd : 1, err : 0201<br>Error! cmd : 1, err : 0201<br>Error! cmd : 1, err : 0201<br>
Error! cmd : 1, err : 0201<br>Error! cmd : 1, err : 0201<br>Error! cmd : 1, err : 0201<br>Error! cmd : 1, err : 0201<br>Error! cmd : 1, err : 0201<br>Error! cmd : 1, err : 0201<br>No MMC card found<br>** Bad partition 1 **<br>
** Bad partition 1 **<br>## Booting image at 00800000 ...<br>Bad Magic Number<br>Marvell&gt;&gt;<br><br>If I issue a printenv, I get the results shown below.<br><br>What is going on?<br><br>The plug runs fine after this manual boot command, but I can&#39;t have a serial connection to it all the time!<br>
<br>Thank,<br>Mark<br><br>printenv results follow:<br><br>Marvell&gt;&gt; printenv<br>baudrate=115200<br>loads_echo=0<br>rootpath=/mnt/ARM_FS/<br>netmask=255.255.0.0<br>console=a0000<br>e=ttyS0,115200<br>CASset=min<br>MALLOC_len=1<br>
ethprime=egiga0<br>bootargs_root=root=/dev/mtdblock2 ro<br>ethmtu=1500<br>usb0Mode=host<br>nandEcc=1bit<br>ethact=egiga0<br>serverip=10.10.0.2<br>ipaddr=10.10.0.1<br>cesvcid=ULULULULULULPPULULULULULDA<br>bootargs_end=:::DB88FXX81:eth0:none<br>
image_name=uImage<br>standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/m<br>tdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;<br>mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs<br>
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500<br>yuk_ethaddr=00:00:00:EE:51:81<br>netretry=no<br>rcvrip=169.254.100.100<br>loadaddr=0x02000000<br>autoload=no<br>ethaddr=00:50:43:01:47:74<br>run_diag=no<br>
arcNumber=2097<br>bootcmd_m0000=0x01100000<br>bootargs_console=console=ttyS0,115200<br>bootcmd_mmc=mmcinit; ext2load mmc 0 0x01100000 /uInitrd; ext2load mmc 0 0x00800000 /uImage<br>bootcmd=setenv bootargs $(bootargs_console); run bootcmd_mmc; bootm 0x00800000 0x01100000<br>
stdin=serial<br>stdout=serial<br>stderr=serial<br>nandEnvBase=a0000<br>mainlineLinux=yes<br>enaMonExt=no<br>enaCpuStream=no<br>enaWrAllo=no<br>pexMode=RC<br>disL2Cache=no<br>setL2CacheWT=yes<br>disL2Prefetch=yes<br>enaICPref=yes<br>
enaDCPref=yes<br>sata_dma_mode=yes<br>netbsd_en=no<br>vxworks_en=no<br>bootdelay=3<br>disaMvPnp=no<br>enaAutoRecovery=yes<br>pcieTune=no<br>bootargs=console=ttyS0,115200<br><br>Environment size: 1366/131068 bytes<br><br>



To UNSUBSCRIBE, email to debian-arm-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Archive: http://lists.debian.org/u2mdcac70cf...6585415633@mail.gmail.com